Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions
- Autores
- Dalibón Bähler, Eugenia Laura; Moreira, Ramiro Damián; Heim, Daniel; Forsich, Christian; Brühl, Sonia Patricia
- Año de publicación
- 2020
- Idioma
- inglés
- Tipo de recurso
- artículo
- Estado
- versión aceptada
- Descripción
- Thick and soft DLC coatings were deposited over stainless steel to improve their surface properties, protecting them from wear in different conditions. When a protective film is thick, it can be considered as selfsustaining in terms of loadcarrying capacity during wear situations even if the substrate is soft or hard. Thin and hard DLC coatings are well known for having high hardness and low friction coefficient; however they have adhesion problems when deposited on soft steels and many of their wear properties also depend on adhesion. For this reason, a previous plasma nitriding process may be convenient. In this work, the fretting and erosion wear behaviour of DLC soft coatings deposited on nitrided and nonnitrided austenitic stainless steel was evaluated using high loads and long tests both simulating severe conditions wear. The aim is to analyse under which conditions the film thickness is not enough to withstand wear damage when deposited onto soft steels. The results showed that in the fretting tests, the duplex sample presented better resistance than the only coated sample in all tested conditions, except for the minimum load, 12 N. In slurry erosion tests, the mass loss was similar in both samples until nine hours, when the influence of the nitrided layer became noticeable as a hard layer since the coating partially removed.
Fil: Dalibón Bähler, Eugenia Laura. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina.
Fil: Moreira, Ramiro Damián. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina.
Fil: Heim, Daniel. Upper Austria University of Applied Sciences; Austria.
Fil: Forsich, Christian. Upper Austria University of Applied Sciences; Austria.
Fil: Brühl, Sonia Patricia. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina.
Peer Reviewed - Materia
-
Thick DLC
Soft carbon coating
Severe wear
Erosion
Fretting - Nivel de accesibilidad
- acceso abierto
- Condiciones de uso
- 2020-12-02T19:44:59Z
- Repositorio
.jpg)
- Institución
- Universidad Tecnológica Nacional
- OAI Identificador
- oai:ria.utn.edu.ar:20.500.12272/4622
Ver los metadatos del registro completo
| id |
RIAUTN_537a662bb27b0bb513294a9581f05c79 |
|---|---|
| oai_identifier_str |
oai:ria.utn.edu.ar:20.500.12272/4622 |
| network_acronym_str |
RIAUTN |
| repository_id_str |
a |
| network_name_str |
Repositorio Institucional Abierto (UTN) |
| spelling |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditionsDalibón Bähler, Eugenia LauraMoreira, Ramiro DamiánHeim, DanielForsich, ChristianBrühl, Sonia PatriciaThick DLCSoft carbon coatingSevere wearErosionFrettingThick and soft DLC coatings were deposited over stainless steel to improve their surface properties, protecting them from wear in different conditions. When a protective film is thick, it can be considered as selfsustaining in terms of loadcarrying capacity during wear situations even if the substrate is soft or hard. Thin and hard DLC coatings are well known for having high hardness and low friction coefficient; however they have adhesion problems when deposited on soft steels and many of their wear properties also depend on adhesion. For this reason, a previous plasma nitriding process may be convenient. In this work, the fretting and erosion wear behaviour of DLC soft coatings deposited on nitrided and nonnitrided austenitic stainless steel was evaluated using high loads and long tests both simulating severe conditions wear. The aim is to analyse under which conditions the film thickness is not enough to withstand wear damage when deposited onto soft steels. The results showed that in the fretting tests, the duplex sample presented better resistance than the only coated sample in all tested conditions, except for the minimum load, 12 N. In slurry erosion tests, the mass loss was similar in both samples until nine hours, when the influence of the nitrided layer became noticeable as a hard layer since the coating partially removed.Fil: Dalibón Bähler, Eugenia Laura. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina.Fil: Moreira, Ramiro Damián. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina.Fil: Heim, Daniel. Upper Austria University of Applied Sciences; Austria.Fil: Forsich, Christian. Upper Austria University of Applied Sciences; Austria.Fil: Brühl, Sonia Patricia. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina.Peer Reviewed2020-12-02T19:44:59Z2020-12-02T19:44:59Z2020info:eu-repo/semantics/articleinfo:eu-repo/semantics/acceptedVersionhttp://purl.org/coar/resource_type/c_6501info:ar-repo/semantics/articuloapplication/pdfapplication/pdfDiamond and Related Materials0925-9635http://hdl.handle.net/20.500.12272/4622enginfo:eu-repo/semantics/openAccess2020-12-02T19:44:59Zhttp://creativecommons.org/licenses/by-nc-nd/4.0/Attribution-NonCommercial-NoDerivatives 4.0 InternacionalDalibón Bähler, Eugenia Laura ; Moreira, Ramiro Damián ; Heim, Daniel ; Forsich, Christian ; Brühl, Sonia PatriciaNo comercial con fines académicos.reponame:Repositorio Institucional Abierto (UTN)instname:Universidad Tecnológica Nacional2026-10-29T11:27:25Zoai:ria.utn.edu.ar:20.500.12272/4622instacron:UTNInstitucionalhttp://ria.utn.edu.ar/Universidad públicaNo correspondehttp://ria.utn.edu.ar/oaigestionria@rec.utn.edu.ar; fsuarez@rec.utn.edu.arArgentinaNo correspondeNo correspondeNo correspondeopendoar:a2026-10-29 11:27:25.512Repositorio Institucional Abierto (UTN) - Universidad Tecnológica Nacionalfalse |
| dc.title.none.fl_str_mv |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions |
| title |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions |
| spellingShingle |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions Dalibón Bähler, Eugenia Laura Thick DLC Soft carbon coating Severe wear Erosion Fretting |
| title_short |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions |
| title_full |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions |
| title_fullStr |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions |
| title_full_unstemmed |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions |
| title_sort |
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions |
| dc.creator.none.fl_str_mv |
Dalibón Bähler, Eugenia Laura Moreira, Ramiro Damián Heim, Daniel Forsich, Christian Brühl, Sonia Patricia |
| author |
Dalibón Bähler, Eugenia Laura |
| author_facet |
Dalibón Bähler, Eugenia Laura Moreira, Ramiro Damián Heim, Daniel Forsich, Christian Brühl, Sonia Patricia |
| author_role |
author |
| author2 |
Moreira, Ramiro Damián Heim, Daniel Forsich, Christian Brühl, Sonia Patricia |
| author2_role |
author author author author |
| dc.subject.none.fl_str_mv |
Thick DLC Soft carbon coating Severe wear Erosion Fretting |
| topic |
Thick DLC Soft carbon coating Severe wear Erosion Fretting |
| dc.description.none.fl_txt_mv |
Thick and soft DLC coatings were deposited over stainless steel to improve their surface properties, protecting them from wear in different conditions. When a protective film is thick, it can be considered as selfsustaining in terms of loadcarrying capacity during wear situations even if the substrate is soft or hard. Thin and hard DLC coatings are well known for having high hardness and low friction coefficient; however they have adhesion problems when deposited on soft steels and many of their wear properties also depend on adhesion. For this reason, a previous plasma nitriding process may be convenient. In this work, the fretting and erosion wear behaviour of DLC soft coatings deposited on nitrided and nonnitrided austenitic stainless steel was evaluated using high loads and long tests both simulating severe conditions wear. The aim is to analyse under which conditions the film thickness is not enough to withstand wear damage when deposited onto soft steels. The results showed that in the fretting tests, the duplex sample presented better resistance than the only coated sample in all tested conditions, except for the minimum load, 12 N. In slurry erosion tests, the mass loss was similar in both samples until nine hours, when the influence of the nitrided layer became noticeable as a hard layer since the coating partially removed. Fil: Dalibón Bähler, Eugenia Laura. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina. Fil: Moreira, Ramiro Damián. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina. Fil: Heim, Daniel. Upper Austria University of Applied Sciences; Austria. Fil: Forsich, Christian. Upper Austria University of Applied Sciences; Austria. Fil: Brühl, Sonia Patricia. Universidad Tecnológica Nacional. Facultad Regional Concepción del Uruguay. Departamento Ingeniería Electromecánica. Grupo de Ingeniería de Superficies; Argentina. Peer Reviewed |
| description |
Thick and soft DLC coatings were deposited over stainless steel to improve their surface properties, protecting them from wear in different conditions. When a protective film is thick, it can be considered as selfsustaining in terms of loadcarrying capacity during wear situations even if the substrate is soft or hard. Thin and hard DLC coatings are well known for having high hardness and low friction coefficient; however they have adhesion problems when deposited on soft steels and many of their wear properties also depend on adhesion. For this reason, a previous plasma nitriding process may be convenient. In this work, the fretting and erosion wear behaviour of DLC soft coatings deposited on nitrided and nonnitrided austenitic stainless steel was evaluated using high loads and long tests both simulating severe conditions wear. The aim is to analyse under which conditions the film thickness is not enough to withstand wear damage when deposited onto soft steels. The results showed that in the fretting tests, the duplex sample presented better resistance than the only coated sample in all tested conditions, except for the minimum load, 12 N. In slurry erosion tests, the mass loss was similar in both samples until nine hours, when the influence of the nitrided layer became noticeable as a hard layer since the coating partially removed. |
| publishDate |
2020 |
| dc.date.none.fl_str_mv |
2020-12-02T19:44:59Z 2020-12-02T19:44:59Z 2020 |
| dc.type.none.fl_str_mv |
info:eu-repo/semantics/article info:eu-repo/semantics/acceptedVersion http://purl.org/coar/resource_type/c_6501 info:ar-repo/semantics/articulo |
| format |
article |
| status_str |
acceptedVersion |
| dc.identifier.none.fl_str_mv |
Diamond and Related Materials 0925-9635 http://hdl.handle.net/20.500.12272/4622 |
| identifier_str_mv |
Diamond and Related Materials 0925-9635 |
| url |
http://hdl.handle.net/20.500.12272/4622 |
| dc.language.none.fl_str_mv |
eng |
| language |
eng |
| dc.rights.none.fl_str_mv |
info:eu-repo/semantics/openAccess 2020-12-02T19:44:59Z http://creativecommons.org/licenses/by-nc-nd/4.0/ Attribution-NonCommercial-NoDerivatives 4.0 Internacional Dalibón Bähler, Eugenia Laura ; Moreira, Ramiro Damián ; Heim, Daniel ; Forsich, Christian ; Brühl, Sonia Patricia No comercial con fines académicos. |
| eu_rights_str_mv |
openAccess |
| rights_invalid_str_mv |
2020-12-02T19:44:59Z http://creativecommons.org/licenses/by-nc-nd/4.0/ Attribution-NonCommercial-NoDerivatives 4.0 Internacional Dalibón Bähler, Eugenia Laura ; Moreira, Ramiro Damián ; Heim, Daniel ; Forsich, Christian ; Brühl, Sonia Patricia No comercial con fines académicos. |
| dc.format.none.fl_str_mv |
application/pdf application/pdf |
| dc.source.none.fl_str_mv |
reponame:Repositorio Institucional Abierto (UTN) instname:Universidad Tecnológica Nacional |
| reponame_str |
Repositorio Institucional Abierto (UTN) |
| collection |
Repositorio Institucional Abierto (UTN) |
| instname_str |
Universidad Tecnológica Nacional |
| repository.name.fl_str_mv |
Repositorio Institucional Abierto (UTN) - Universidad Tecnológica Nacional |
| repository.mail.fl_str_mv |
gestionria@rec.utn.edu.ar; fsuarez@rec.utn.edu.ar |
| _version_ |
1880396323718430720 |
| score |
13.334379 |