On the Double-Arcing Phenomenon in a Cutting Arc Torch.
- Autores
- Prevosto, Leandro; Kelly, Héctor; Mancinelli, Beatriz
- Año de publicación
- 2011
- Idioma
- inglés
- Tipo de recurso
- artículo
- Estado
- versión aceptada
- Descripción
- Transferred arc plasma torches are widely used in industrial cutting process of metallic materials because of their ability to cut almost any metal and the very high productivity that can be achieved with this technology (Boulos et al., 1994). The plasma cutting process is characterized by a transferred electric arc that is established between a cathode, which is a part of the cutting torch, and a work-piece (the metal to be cut) acting as the anode. In order to obtain a high-quality cut, the plasma jet must be as collimated as possible and also must have a high power density. To this end, the transferred arc is constricted by a metallic tube (a nozzle) with a small inner diameter (of the order of one millimeter). Usually, a vortex-type flow with large axial and azimuthal velocity components is forced through the nozzle to provide arc stability and to protect its inner wall. In such case the hot arc is confined to the center of the nozzle, while centrifugal forces drive the colder fluid towards the nozzle walls, which are thus thermally protected. The axial component of the gas flow continuously supplies cold fluid, providing an intense convective cooling at the arc fringes. In addition, the vortex flow enhances the power dissipation per unit length of the arc column, resulting in high temperatures at the arc axis. Since the nozzle is subjected to a very high heat flux, it is made of a metal with a high thermal conductivity (copper is broadly used). The arc current is of the order of ten up to a few hundred amperes, and the gas pressure is several atmospheres. Arc axis temperatures around 15 kK are usual, but larger values, close to 25 kK or even higher, have been reached.
Fil: Prevosto, Leandro. Universidad Tecnológica Nacional. Facultad Regional Venado Tuerto. Departamento Ingeniería Electromecánica. Grupo de Descargas Eléctricas. Santa Fe; Argentina.
Fil: Kelly, Héctor. Facultad de Ciencias Exactas y Naturales (UBA). Departamento de Física. Instituto de Física ( CONICET). Buenos Aires; Argentina.
Fil: Mancinelli, Beatriz. Universidad Tecnológica Nacional. Facultad Regional Venado Tuerto. Departamento Ingeniería Electromecánica. Grupo de Descargas Eléctricas. Santa Fe; Argentina.
Peer Reviewed - Fuente
- umerical Simulations of Physical and Engineering Processes.(cáp. 23, pág 504-524).
- Materia
-
Double-Arcing.
Cutting Arc Torch.
Plasma. - Nivel de accesibilidad
- acceso abierto
- Condiciones de uso
- 2024-04-05T00:30:19Z
- Repositorio
.jpg)
- Institución
- Universidad Tecnológica Nacional
- OAI Identificador
- oai:ria.utn.edu.ar:20.500.12272/10345
Ver los metadatos del registro completo
| id |
RIAUTN_5aa7503727d12a3371e19f130fa26a05 |
|---|---|
| oai_identifier_str |
oai:ria.utn.edu.ar:20.500.12272/10345 |
| network_acronym_str |
RIAUTN |
| repository_id_str |
a |
| network_name_str |
Repositorio Institucional Abierto (UTN) |
| spelling |
On the Double-Arcing Phenomenon in a Cutting Arc Torch.Prevosto, LeandroKelly, HéctorMancinelli, BeatrizDouble-Arcing.Cutting Arc Torch.Plasma.Transferred arc plasma torches are widely used in industrial cutting process of metallic materials because of their ability to cut almost any metal and the very high productivity that can be achieved with this technology (Boulos et al., 1994). The plasma cutting process is characterized by a transferred electric arc that is established between a cathode, which is a part of the cutting torch, and a work-piece (the metal to be cut) acting as the anode. In order to obtain a high-quality cut, the plasma jet must be as collimated as possible and also must have a high power density. To this end, the transferred arc is constricted by a metallic tube (a nozzle) with a small inner diameter (of the order of one millimeter). Usually, a vortex-type flow with large axial and azimuthal velocity components is forced through the nozzle to provide arc stability and to protect its inner wall. In such case the hot arc is confined to the center of the nozzle, while centrifugal forces drive the colder fluid towards the nozzle walls, which are thus thermally protected. The axial component of the gas flow continuously supplies cold fluid, providing an intense convective cooling at the arc fringes. In addition, the vortex flow enhances the power dissipation per unit length of the arc column, resulting in high temperatures at the arc axis. Since the nozzle is subjected to a very high heat flux, it is made of a metal with a high thermal conductivity (copper is broadly used). The arc current is of the order of ten up to a few hundred amperes, and the gas pressure is several atmospheres. Arc axis temperatures around 15 kK are usual, but larger values, close to 25 kK or even higher, have been reached.Fil: Prevosto, Leandro. Universidad Tecnológica Nacional. Facultad Regional Venado Tuerto. Departamento Ingeniería Electromecánica. Grupo de Descargas Eléctricas. Santa Fe; Argentina.Fil: Kelly, Héctor. Facultad de Ciencias Exactas y Naturales (UBA). Departamento de Física. Instituto de Física ( CONICET). Buenos Aires; Argentina.Fil: Mancinelli, Beatriz. Universidad Tecnológica Nacional. Facultad Regional Venado Tuerto. Departamento Ingeniería Electromecánica. Grupo de Descargas Eléctricas. Santa Fe; Argentina.Peer Reviewed2024-04-05T00:30:19Z2024-04-05T00:30:19Z2011info:eu-repo/semantics/articleinfo:eu-repo/semantics/acceptedVersionhttp://purl.org/coar/resource_type/c_6501info:ar-repo/semantics/articulopdfapplication/pdfInTech.978-953-307-620-1http://hdl.handle.net/20.500.12272/10345umerical Simulations of Physical and Engineering Processes.(cáp. 23, pág 504-524).reponame:Repositorio Institucional Abierto (UTN)instname:Universidad Tecnológica Nacionalenginfo:eu-repo/semantics/openAccess2024-04-05T00:30:19Zhttp://creativecommons.org/licenses/by-nc-nd/4.0/Attribution-NonCommercial-NoDerivatives 4.0 InternacionalPrevosto, Leandro.Creative Commons http://creativecommons.org/licenses/by-nc-nd/4.0/ Attribution-NonCommercial-NoDerivatives 4.0 Internacional Este trabajo puede ser utilizado con fines académicos y de estudio.2026-10-29T11:27:38Zoai:ria.utn.edu.ar:20.500.12272/10345instacron:UTNInstitucionalhttp://ria.utn.edu.ar/Universidad públicaNo correspondehttp://ria.utn.edu.ar/oaigestionria@rec.utn.edu.ar; fsuarez@rec.utn.edu.arArgentinaNo correspondeNo correspondeNo correspondeopendoar:a2026-10-29 11:27:39.323Repositorio Institucional Abierto (UTN) - Universidad Tecnológica Nacionalfalse |
| dc.title.none.fl_str_mv |
On the Double-Arcing Phenomenon in a Cutting Arc Torch. |
| title |
On the Double-Arcing Phenomenon in a Cutting Arc Torch. |
| spellingShingle |
On the Double-Arcing Phenomenon in a Cutting Arc Torch. Prevosto, Leandro Double-Arcing. Cutting Arc Torch. Plasma. |
| title_short |
On the Double-Arcing Phenomenon in a Cutting Arc Torch. |
| title_full |
On the Double-Arcing Phenomenon in a Cutting Arc Torch. |
| title_fullStr |
On the Double-Arcing Phenomenon in a Cutting Arc Torch. |
| title_full_unstemmed |
On the Double-Arcing Phenomenon in a Cutting Arc Torch. |
| title_sort |
On the Double-Arcing Phenomenon in a Cutting Arc Torch. |
| dc.creator.none.fl_str_mv |
Prevosto, Leandro Kelly, Héctor Mancinelli, Beatriz |
| author |
Prevosto, Leandro |
| author_facet |
Prevosto, Leandro Kelly, Héctor Mancinelli, Beatriz |
| author_role |
author |
| author2 |
Kelly, Héctor Mancinelli, Beatriz |
| author2_role |
author author |
| dc.subject.none.fl_str_mv |
Double-Arcing. Cutting Arc Torch. Plasma. |
| topic |
Double-Arcing. Cutting Arc Torch. Plasma. |
| dc.description.none.fl_txt_mv |
Transferred arc plasma torches are widely used in industrial cutting process of metallic materials because of their ability to cut almost any metal and the very high productivity that can be achieved with this technology (Boulos et al., 1994). The plasma cutting process is characterized by a transferred electric arc that is established between a cathode, which is a part of the cutting torch, and a work-piece (the metal to be cut) acting as the anode. In order to obtain a high-quality cut, the plasma jet must be as collimated as possible and also must have a high power density. To this end, the transferred arc is constricted by a metallic tube (a nozzle) with a small inner diameter (of the order of one millimeter). Usually, a vortex-type flow with large axial and azimuthal velocity components is forced through the nozzle to provide arc stability and to protect its inner wall. In such case the hot arc is confined to the center of the nozzle, while centrifugal forces drive the colder fluid towards the nozzle walls, which are thus thermally protected. The axial component of the gas flow continuously supplies cold fluid, providing an intense convective cooling at the arc fringes. In addition, the vortex flow enhances the power dissipation per unit length of the arc column, resulting in high temperatures at the arc axis. Since the nozzle is subjected to a very high heat flux, it is made of a metal with a high thermal conductivity (copper is broadly used). The arc current is of the order of ten up to a few hundred amperes, and the gas pressure is several atmospheres. Arc axis temperatures around 15 kK are usual, but larger values, close to 25 kK or even higher, have been reached. Fil: Prevosto, Leandro. Universidad Tecnológica Nacional. Facultad Regional Venado Tuerto. Departamento Ingeniería Electromecánica. Grupo de Descargas Eléctricas. Santa Fe; Argentina. Fil: Kelly, Héctor. Facultad de Ciencias Exactas y Naturales (UBA). Departamento de Física. Instituto de Física ( CONICET). Buenos Aires; Argentina. Fil: Mancinelli, Beatriz. Universidad Tecnológica Nacional. Facultad Regional Venado Tuerto. Departamento Ingeniería Electromecánica. Grupo de Descargas Eléctricas. Santa Fe; Argentina. Peer Reviewed |
| description |
Transferred arc plasma torches are widely used in industrial cutting process of metallic materials because of their ability to cut almost any metal and the very high productivity that can be achieved with this technology (Boulos et al., 1994). The plasma cutting process is characterized by a transferred electric arc that is established between a cathode, which is a part of the cutting torch, and a work-piece (the metal to be cut) acting as the anode. In order to obtain a high-quality cut, the plasma jet must be as collimated as possible and also must have a high power density. To this end, the transferred arc is constricted by a metallic tube (a nozzle) with a small inner diameter (of the order of one millimeter). Usually, a vortex-type flow with large axial and azimuthal velocity components is forced through the nozzle to provide arc stability and to protect its inner wall. In such case the hot arc is confined to the center of the nozzle, while centrifugal forces drive the colder fluid towards the nozzle walls, which are thus thermally protected. The axial component of the gas flow continuously supplies cold fluid, providing an intense convective cooling at the arc fringes. In addition, the vortex flow enhances the power dissipation per unit length of the arc column, resulting in high temperatures at the arc axis. Since the nozzle is subjected to a very high heat flux, it is made of a metal with a high thermal conductivity (copper is broadly used). The arc current is of the order of ten up to a few hundred amperes, and the gas pressure is several atmospheres. Arc axis temperatures around 15 kK are usual, but larger values, close to 25 kK or even higher, have been reached. |
| publishDate |
2011 |
| dc.date.none.fl_str_mv |
2011 2024-04-05T00:30:19Z 2024-04-05T00:30:19Z |
| dc.type.none.fl_str_mv |
info:eu-repo/semantics/article info:eu-repo/semantics/acceptedVersion http://purl.org/coar/resource_type/c_6501 info:ar-repo/semantics/articulo |
| format |
article |
| status_str |
acceptedVersion |
| dc.identifier.none.fl_str_mv |
InTech. 978-953-307-620-1 http://hdl.handle.net/20.500.12272/10345 |
| identifier_str_mv |
InTech. 978-953-307-620-1 |
| url |
http://hdl.handle.net/20.500.12272/10345 |
| dc.language.none.fl_str_mv |
eng |
| language |
eng |
| dc.rights.none.fl_str_mv |
info:eu-repo/semantics/openAccess 2024-04-05T00:30:19Z http://creativecommons.org/licenses/by-nc-nd/4.0/ Attribution-NonCommercial-NoDerivatives 4.0 Internacional Prevosto, Leandro. Creative Commons http://creativecommons.org/licenses/by-nc-nd/4.0/ Attribution-NonCommercial-NoDerivatives 4.0 Internacional Este trabajo puede ser utilizado con fines académicos y de estudio. |
| eu_rights_str_mv |
openAccess |
| rights_invalid_str_mv |
2024-04-05T00:30:19Z http://creativecommons.org/licenses/by-nc-nd/4.0/ Attribution-NonCommercial-NoDerivatives 4.0 Internacional Prevosto, Leandro. Creative Commons http://creativecommons.org/licenses/by-nc-nd/4.0/ Attribution-NonCommercial-NoDerivatives 4.0 Internacional Este trabajo puede ser utilizado con fines académicos y de estudio. |
| dc.format.none.fl_str_mv |
pdf application/pdf |
| dc.source.none.fl_str_mv |
umerical Simulations of Physical and Engineering Processes.(cáp. 23, pág 504-524). reponame:Repositorio Institucional Abierto (UTN) instname:Universidad Tecnológica Nacional |
| reponame_str |
Repositorio Institucional Abierto (UTN) |
| collection |
Repositorio Institucional Abierto (UTN) |
| instname_str |
Universidad Tecnológica Nacional |
| repository.name.fl_str_mv |
Repositorio Institucional Abierto (UTN) - Universidad Tecnológica Nacional |
| repository.mail.fl_str_mv |
gestionria@rec.utn.edu.ar; fsuarez@rec.utn.edu.ar |
| _version_ |
1880396327759642624 |
| score |
13.334379 |